EPO waterproof coating series




  • GERMANY VESCHKO 

    EPO-CR Waterproof Coating 

    Uses 

    • As a waterproofing membrane with EPO-CR.

    • As a coating membrane mixed with EPO-CR Quartz Sand Mixture .

    • The use of waterproof coating and non-woven fabrics, and enhance the extension of the roof.

    - Concrete roof, concrete floor, concrete wall ;

    - floors of winter gardens, in commercial, retail and leisure premises, garages and basements ;

    •For new construction and repair projects.

    Features 

    Anti-aging, resistance to high temperature, waterproof anti-corrosion, can be exposed to use

    CE-Marking 

    Component to 2

    ETA 03/0043

    Water vapour diffusion factor μ

    ~100

    Resistance to wind loads

    >= 55 kPa

    substances

    Concrete roofing

    Imposed loads

    P1 to P4

    Roof slope

    S1 to S4

    Lowest surface temperature

    TL4

    Highest surface temperature

    TH4


     Composition
     

    EPO-CR and non-woven fabrics used in conjunction with, EPO-CR should be uniform mixing, the non-woven fabric soak them.

      

    Pack sizes

    20kg

    Shelf Life 

    Can be stored unopened for up to 1 year in a cool, dry, frost-free place 

    Properties

    Form

    liquid, one-component


    Standard colour

    light grey,dark grey


    Special colours
     on request
    Workability period* [min]
     approx. 30
    Rainproof* after [h]
    Approx.3-6
    Can be walked on* after [h]
    approx. 24
    Repair* after [d]
     approx. 2-3
    Next coat can be applied after* [h]

     Approx.24 (seerear page)


    * Values obtained at a temperature of 23 °C - 50 % rel. humidity. May vary according to weather conditions such as wind, humidity and temperature. 

    Usage guide

    Depending on the nature and condition of the substrate and on the Non-woven Fabrics to be used: 

    Approx. 2.2 kg/m2 giving a coating thickness of 1.5 mm. 

    Approx. 3.0 kg/m2 giving a coating thickness of 2.0 mm 

    Application 

    Base surface pretreatment: 

    Base surface must be solid and clean, no dust, oil or debris. Base surface such as broken, loose or uneven, after cleaning can be cleaned EPO waterproof anti-corrosion mortar (EPO-CS) for smoothing. Plane construction should follow the direction of drainage with polymer mortar or EPO waterproof coating to do slope. 

    Instructions:

     Stir well before using. If you feel the use of brushing difficult, according to the situation plus 5% -15% water dilution, and stir evenly. Can be roller, brush and spray method of construction. General requirements four times waterproof construction, after the first pass coating dry film before the second track construction.

    Precautions:

    Should be in the appropriate degree of environmental temperature construction.

    Is expected within 24 hours of precipitation and wind dust weather should not be outdoor construction.

    Do not immediately use the paint is strictly prohibited to add water dilution, reclaim cover immediately after the lid to prevent moisture evaporation and crust.

      The same facade is best to use a batch of products, different batches of products for the same facade, should be mixed evenly after use to avoid color.

    Remark 

    High temperature stability, can reach 210℃, 0.5 hours does not flow; 100℃ 4 hours without sticky.

    Important notice  

    For chemical resistance, see the Chemical Resistance List A-Z. 

    The safety data sheets, identification of the units, hazard warnings and safety recommendations on the units must be observed during transportation, storage and application. The BG-Chemie technical information must be observed for application.

    General information  

    We guarantee the consistent high quality of our products.

    VESCHKO products must not be mixed with other manufacturers′ products.

    The technical information and application instructions contained herein reflect the current level of knowledge and experience with our products. In each case, the new edition supersedes the previous technical information and renders it invalid. It is therefore necessary that you always have to hand the current code of practice. When using our products, a detailed, object-related and qualified inspection is required in each individual case in order to determine whether the product and / or application technology in question meets the specific requirements and purposes. We are liable only for our products being free from faults-correct application of our products therefore falls entirely within your scope of liability and responsibility. Our products are sold exclusively on the basis of our conditions of sale and delivery.

    Published: VESCHKO January 2008

      ______________________________________________________________________________________________________________

  • GERMANY VESCHKO IHL Co.   www.veschko.com · Certified according to DIN EN ISO 9001:2000 and DIN EN ISO 14001